Metal Roofing Installation in South Salt Lake, Utah

Metal roofing can be attractive when the goal is a durable, long-lasting roof rather than the lowest upfront cost; durability is not automatic because coating, attachment, flashing and panel design all matter.

Median year built from the US Census American Community Survey; elevation from USGS.

If the roof already needs complete replacement, the project can be evaluated for either metal or asphalt; that timing allows the roof deck to be checked while the homeowner compares the two roofing systems.

Attic ventilation still matters below a metal roof; we check existing ventilation and insulation so the roof assembly can manage heat and moisture below the panels.

Roof temperature and indoor comfort depend on more than whether the outer surface is metal; the selected finish and the insulation and ventilation below it all influence performance, and lighter or reflective coatings can reduce solar heat absorption.

Metal roofing sheds water rapidly, placing more demand on valleys, eaves and gutters; we pay close attention to drainage geometry so water does not overwhelm a valley or roof edge.

The panel is the main exposed surface, while hidden and perimeter components complete the roof; the layers below and the flashing around the panels need to accommodate both drainage and temperature-related movement.

• Metal panels: The finished panels serve as the visible outer roof surface; the selected product determines panel profile, width, seam design, thickness and finish.
• Underlayment: The protective underlayment belongs over the roof deck beneath the metal roofing to protect the roof below the panels, with the exact material based on the roofing system and project details.
• Clips or fasteners: With standing seam, the roof usually conceals the main clips or fasteners below the finished surface, in contrast with exposed-fastener panels, which use visible screws fitted with sealing washers.
• Seams: Roof seams connect adjacent metal panels, while standing seam positions the joint above the panel's main drainage area.
• Flashing and trim: Roof flashing and trim carry roof water around valleys, ridges, walls, chimneys and perimeter edges so water does not rely on surface sealant at major transitions.
• Closures and sealants: The selected system may call for formed closures, compatible sealants or both to seal designated joints against weather and debris.

A premium residential metal roof in South Salt Lake usually means standing seam; exposed-fastener panels are less expensive but leave the attachment hardware exposed over the life of the roof.

• Standing seam: The standing-seam system provides raised seams and concealed clips or fastening for a streamlined residential metal-roof surface.
• Exposed-fastener panels: With exposed-fastener metal roofing, screws and sealing washers remain visible, which means the roof can cost less initially but has more exposed hardware to maintain.
• Metal roof accents: Metal is also an option for smaller sections such as porches, bays and dormers when a full metal-roof replacement is not part of the project.

A proper metal-roof installation begins with the conditions below the panels; we inspect the roof underneath, build the protective layers and attachment, then install and finish the metal panels.

• Plan for expansion and contraction: Metal roofing changes dimension as the roof heats and cools, which is why panel layout and attachment cannot unnecessarily lock the metal in place.
• Build valleys and wall transitions: We build water-control flashing where valleys, walls, chimneys and adjoining roof surfaces meet to guide roof water through each change in direction.
• Finish ridges and roof edges: The perimeter work includes caps, trim and closures designed for the selected panel system to close and protect the places where the panel system ends.
• Plan snow retention where needed: On roof areas where sliding snow could land on frequently used areas below the eaves, we plan snow control as part of the roofing design.
• Use compatible underlayment: We select a compatible underlayment for the exact metal system being installed; we also check that the product is rated for use beneath metal roofing.
• Install the panel attachment system: Standing-seam roofing typically conceals its main clips or fasteners, in contrast with exposed-fastener panels, which use visible screws with sealing washers, and we match the attachment method to the selected roofing system.
• Inspect the wooden roof deck: We check that the roof deck is sound enough for panel alignment and attachment; damaged wood is photographed before we explain and complete the additional repair.

Metal rewards careful work at the transitions more than any other roofing material. The panels are the straightforward part; the valleys, ridges and wall joints are what decide whether the roof reaches its lifespan.

For the full picture of the service, see Metal Roofing.

The panel system is measured and planned before the installation moves onto the roof; we move from roof preparation to protective layers, panel installation and the final water-control details.

1. Plan before fabricationBefore panels are fabricated, we verify measurements, panel layout, openings, transitions and required panel lengths because metal panels are difficult to change once fabricated.
2. Prepare a flat, sound surfaceWe prepare the surface that will support the metal panels and correct problems that could affect installation; we make sure hidden deck problems do not interfere with the new system as part of preparing the roof.
3. Install underlayment and starter detailsNext we install underlayment along with the starter and lower-edge details so those hidden details are complete first.
4. Install and secure the metal roofThe metal panels are installed using the clips or fasteners specified for the roofing system without unnecessarily restricting normal thermal movement.
5. Inspect every transitionBefore final cleanup, we review the seams and every major change in roof direction to make sure runoff has a clear path through each transition.

Courtland Roofing installs metal roofs for South Salt Lake homes with a licensed, insured and family-owned team, backed by our 5-year workmanship warranty on installation.

Certified installer for GAF, CertainTeed and Owens Corning, family-owned, licensed & insured.

Courtland Roofing has installed metal roofs in every part of South Salt Lake, Utah (84115, 84119 and 84106), and we would be glad to look at yours. We give homeowners across the rest of Salt Lake County the same service, including in White City, Copperton and Emigration Canyon.

If you do not see your ZIP code listed, call or text us. We can confirm whether we provide metal roofing at your address in South Salt Lake.