Metal Roofing Installation in Salt Lake City, Utah

Metal roofing offers choices that asphalt shingles do not; standing seam and exposed-fastener systems handle attachment differently, so appearance, roof geometry, budget and expected ownership all matter.

Median year built from the US Census American Community Survey; elevation from USGS.

Metal is often selected over asphalt because the homeowner is looking beyond the lowest initial cost; appearance, expected ownership, snow conditions and wind exposure can all affect whether the added investment is worthwhile.

Open wind exposure makes the attachment system and perimeter details especially important; poorly installed clips or edge trim can undermine an otherwise strong panel system.

A metal roof can shed water efficiently while still depending on properly sized drainage details; the lower roof details need enough capacity to keep water from backing up at joints or edges.

Before planning metal over an older Salt Lake City roof with multiple layers, we need to understand what is underneath, and removing the existing roofing gives the clearest view of the deck and old flashing.

The finished roof combines the metal surface with hidden attachment and water-control materials; the system depends on panels, underlayment, attachment, seams and flashing working together.

• Metal panels: The metal panels make up the main weather-facing surface; the selected product determines panel profile, width, seam design, thickness and finish.
• Underlayment: A compatible underlayment goes between the wooden roof deck and the metal panels to protect the roof below the panels, with the exact material based on the roofing system and project details.
• Clips or fasteners: Standing-seam panels typically rely on clips or fasteners beneath the panels, in contrast with exposed-fastener panels, which use visible screws fitted with sealing washers.
• Seams: Each seam joins one metal panel to the next, while standing seam positions the joint above the panel's main drainage area.
• Flashing and trim: Metal trim and flashing route water around valleys, ridges, walls, chimneys and roof edges so water does not rely on surface sealant at major transitions.
• Closures and sealants: Specific metal-roof connections may need shaped closures or sealants specified for the system to seal designated joints against weather and debris.

For Salt Lake City homeowners, standing seam offers concealed attachment and a cleaner finish, while exposed-fastener metal is a simpler, lower-cost system with more fastener maintenance.

• Standing seam: With standing seam, the roof has raised panel seams with concealed attachment for a streamlined residential metal-roof surface.
• Exposed-fastener panels: These panels fasten through the visible surface with screws and sealing washers, so the roof can cost less initially but has more exposed hardware to maintain.
• Metal roof accents: A project can use metal for porches, bays, dormers and other smaller roof sections when a full metal-roof replacement is not part of the project.

A complete project includes the supporting surface as well as the finished metal; we inspect the roof underneath, build the protective layers and attachment, then install and finish the metal panels.

• Use compatible underlayment: We match the underlayment to the metal system instead of treating it like an asphalt-shingle roof; we also check that the product is rated for use beneath metal roofing.
• Plan snow retention where needed: When a roof can release snow toward people, vehicles, decks, walkways or landscaping, we plan snow control as part of the roofing design.
• Finish ridges and roof edges: We complete the ridge, eave and rake trim along with system-specific closures to close and protect the places where the panel system ends.
• Build valleys and wall transitions: Metal flashing is built around valleys, walls, chimneys and other major transitions to guide roof water through each change in direction.
• Plan for expansion and contraction: Metal panels change length with temperature changes, which is why panel layout and attachment cannot unnecessarily lock the metal in place.
• Detail roof openings: Every vent, pipe, skylight and similar roof opening needs properly fitted metal flashing to move water past the opening without relying on surface sealant alone.
• Install the panel attachment system: The standing-seam system keeps its primary attachment below the visible surface, while exposed-fastener systems leave screws and washers visible, and we match the attachment method to the selected roofing system.

Metal rewards careful work at the transitions more than any other roofing material. The panels are the straightforward part; the valleys, ridges and wall joints are what decide whether the roof reaches its lifespan.

For the full picture of the service, see Metal Roofing.

We establish the panel layout before preparing the roof for installation; we move from roof preparation to protective layers, panel installation and the final water-control details.

1. Confirm the panel systemWe review and finalize panel type, profile, finish, seam style and project details before the panels are fabricated.
2. Expose and correct the roof surfaceWe prepare the wooden roof deck and supporting surface so damage or uneven areas can be corrected before panel layout.
3. Set the protective layersBefore the panels go on, we complete underlayment and the hidden water-control details so hidden protection is complete first.
4. Lay out and install the panelsThe crew positions and fastens the panels using the attachment method required by the roofing system with normal panel movement accounted for.
5. Complete the metal detailsWe complete the ridges, valleys, walls, edges and openings to complete the water-control system around the panels.

Courtland Roofing works with Salt Lake City homeowners to decide whether metal is worth the added cost and to explain the installation requirements of the panel system that fits the roof.

Certified installer for GAF, CertainTeed and Owens Corning, family-owned, licensed & insured.

Courtland Roofing has installed metal roofs in every part of Salt Lake City, Utah, including Foothill, Central City and The Avenues. Those are Salt Lake City neighborhoods we have worked in, and they are examples, not a boundary:

If you do not see your street listed, call or text us. We can confirm whether we provide metal roofing at your address in Salt Lake City.