Flat and Low-Slope Roofing in Murray, Utah

Flat roofing in Murray is mainly a water-management system. The membrane provides the waterproof surface, but the roof still depends on slope, drains, flashing, curbs, and seams. If one of those pieces is poorly designed or damaged, water can remain on the roof or work into the system.

Median year built from the US Census American Community Survey; elevation from USGS.

Schedule a low-slope roof evaluation in Murray when you notice recurring ponding, lifted seams, cracks, bubbles, soft areas underfoot, damaged flashing, or water staining inside. The earlier we understand why water is staying on the roof, the easier it is to separate a drainage problem from a membrane failure.

Drainage is one of the first things we evaluate on a Murray low-slope roof. We look at where water collects, whether drains or scuppers are positioned well, and whether the roof surface directs water toward them instead of trapping it in low areas.

Summer sun affects flat-roof membranes in Murray because the roof surface receives direct exposure for long periods. Reflective membranes such as white TPO can reduce surface heat compared with darker roofing surfaces, although actual building heat performance also depends on insulation and the full roof assembly.

Wind exposure still matters on a flat roof in Murray. Membranes, edge metal, corners, parapets, and rooftop equipment all need secure attachment because uplift forces are often strongest around the roof perimeter and corners.

A Murray low-slope roof can use several membrane systems. TPO uses thermoplastic sheets with heat-welded seams. EPDM uses a rubber membrane with compatible seam and flashing details. Modified bitumen uses reinforced asphalt-based sheets. Each system handles details and repairs differently, so the existing roof and drainage layout matter when choosing between them.

• TPO single-ply membrane: TPO is a thermoplastic roofing membrane. Seams are joined with heat-welding equipment so separate sheets become part of one continuous roof surface.
• EPDM rubber membrane: EPDM is a flexible synthetic rubber membrane. Seams and roof details use compatible adhesives, tapes, or flashing products designed for the system.
• Modified bitumen: Modified bitumen is an asphalt-based low-slope membrane reinforced for roofing use. It can be practical on smaller flat sections, porches, garages, and similar areas.
• Existing membrane repairs: We can inspect existing flat-roof membranes for open seams, damaged flashing, punctures, failed details, and drainage problems before recommending repair or replacement.

A low-slope roofing project in Murray starts with understanding how the roof handles water. We inspect drainage, membrane condition, substrate, seams, edges, and penetrations before deciding what work is appropriate.

• Check the substrate and insulation: We look for soft areas, trapped moisture, damaged insulation, or substrate problems that should not be covered by a new membrane.
• Install the membrane: The membrane is laid out and attached according to the selected system. TPO seams are heat welded, while EPDM and modified-bitumen systems use their approved joining methods.
• Assess drainage first: We identify where water currently flows, where it stands, and whether drains, scuppers, gutters, or roof edges are handling runoff correctly.
• Build roof edges and transitions: Edges, parapets, wall transitions, and termination points are finished so wind and water cannot work behind the membrane.
• Prepare the roof surface: The membrane needs a clean, stable surface. Preparation depends on whether the project involves tear-off, recovery, insulation replacement, or work over an existing approved substrate.
• Test and inspect seams: We inspect completed seams and details before the roof is considered finished. On applicable systems, seams can be probed or otherwise checked for continuity.

Which of those apply depends on what the inspection finds. We would rather tell you the roof needs a repair than sell you a replacement it does not need yet.

For the full picture of the service, see Flat Roofing.

Flat roofing in Murray follows a different sequence from shingle work because drainage and membrane continuity have to be addressed before the roof is considered watertight.

1. Inspect the existing roofWe document membrane condition, drainage, penetrations, repairs, roof edges, and any areas that stay wet.
2. Confirm the roofing approachWe determine whether the project calls for repair, partial replacement, recovery, or full tear-off based on the condition of the existing system.
3. Correct approved substrate issuesDamaged insulation, wet materials, and unsound surfaces are addressed before the new membrane covers them.
4. Install the low-slope roofing systemThe membrane and its seams are installed according to the selected product and attachment method.
5. Check drainage and detailsWe review drains, scuppers, edges, walls, curbs, and penetrations because those areas control how the completed roof handles water.

Courtland Roofing installs and repairs flat and low-slope roofing in Murray. We are family-owned, licensed, and insured. We treat drainage, substrate condition, seams, penetrations, and roof edges as part of the same roofing system rather than focusing only on the membrane surface.

Certified installer for GAF, CertainTeed and Owens Corning, family-owned, licensed & insured.

Courtland Roofing has worked on flat roofs in every part of Murray, Utah (84107, 84123, 84121 and 84117), including the streets around Murray Park and Fashion Place. We give homeowners across the rest of Salt Lake County the same service, including in South Salt Lake, Millcreek and Bluffdale.

If you do not see your ZIP code listed, call or text us. We can confirm whether we provide flat and low-slope roofing at your address in Murray.