Flat and Low-Slope Roofing in South Jordan, Utah

Low-slope roofs in South Jordan carry water differently from pitched roofs. Because runoff is slower, weak seams, poorly detailed drains, and low spots can stay wet longer. The roofing system has to be designed so water can leave the roof without sitting against vulnerable details.

Median year built from the US Census American Community Survey; elevation from USGS.

Flat-roof problems in South Jordan often show up as standing water, seam movement, membrane wear, or leaks around drains and penetrations. A roof that still holds water well after normal drainage should be inspected because repeated ponding can accelerate wear at weak points.

Skylights and roof curbs need special attention on a low-slope roof in South Jordan. Water moves more slowly around these raised openings, so the membrane flashing has to turn up the curb and stay watertight at corners and transitions.

Moisture below a low-slope roof matters as much as the membrane above it. We look for signs of trapped moisture in insulation or the substrate because covering wet materials with a new membrane can leave the underlying problem in place.

Winter drainage is important on South Jordan flat roofs. Snow can melt during warmer periods and refreeze near drains or edges. We pay attention to where water moves, where ice may restrict drainage, and whether low areas are likely to hold moisture for long periods.

A South Jordan low-slope roof can use several membrane systems. TPO uses thermoplastic sheets with heat-welded seams. EPDM uses a rubber membrane with compatible seam and flashing details. Modified bitumen uses reinforced asphalt-based sheets. Each system handles details and repairs differently, so the existing roof and drainage layout matter when choosing between them.

• TPO single-ply membrane: TPO is a thermoplastic roofing membrane. Seams are joined with heat-welding equipment so separate sheets become part of one continuous roof surface.
• EPDM rubber membrane: EPDM is a flexible synthetic rubber membrane. Seams and roof details use compatible adhesives, tapes, or flashing products designed for the system.
• Modified bitumen: Modified bitumen is an asphalt-based low-slope membrane reinforced for roofing use. It can be practical on smaller flat sections, porches, garages, and similar areas.
• Existing membrane repairs: We can inspect existing flat-roof membranes for open seams, damaged flashing, punctures, failed details, and drainage problems before recommending repair or replacement.

A low-slope roofing project in South Jordan starts with understanding how the roof handles water. We inspect drainage, membrane condition, substrate, seams, edges, and penetrations before deciding what work is appropriate.

• Detail drains and penetrations: Drains, vents, pipes, skylight curbs, walls, and rooftop equipment receive membrane flashing designed for the selected roofing system.
• Check the substrate and insulation: We look for soft areas, trapped moisture, damaged insulation, or substrate problems that should not be covered by a new membrane.
• Prepare the roof surface: The membrane needs a clean, stable surface. Preparation depends on whether the project involves tear-off, recovery, insulation replacement, or work over an existing approved substrate.
• Install the membrane: The membrane is laid out and attached according to the selected system. TPO seams are heat welded, while EPDM and modified-bitumen systems use their approved joining methods.
• Assess drainage first: We identify where water currently flows, where it stands, and whether drains, scuppers, gutters, or roof edges are handling runoff correctly.
• Test and inspect seams: We inspect completed seams and details before the roof is considered finished. On applicable systems, seams can be probed or otherwise checked for continuity.

Which of those apply depends on what the inspection finds. We would rather tell you the roof needs a repair than sell you a replacement it does not need yet.

For the full picture of the service, see Flat Roofing.

Flat roofing in South Jordan follows a different sequence from shingle work because drainage and membrane continuity have to be addressed before the roof is considered watertight.

1. Find the drainage problem firstBefore changing the membrane, we determine whether the roof is holding water because of clogged drainage, poor slope, settled insulation, or another condition.
2. Open up suspect areas when neededIf trapped moisture is suspected, the roof assembly may need targeted investigation before a new membrane is installed.
3. Build a sound substrateWet or damaged materials are addressed as part of the approved scope so the new roof is not installed over a failing base.
4. Install and join the membraneSeams are welded, taped, adhered, or otherwise completed according to the selected roofing system.
5. Finish every transitionEdges, walls, curbs, drains, vents, and other interruptions are completed before the roof is signed off.

Courtland Roofing provides flat and low-slope roofing services in South Jordan. We evaluate the drainage first, inspect for trapped moisture or damaged substrate, and then recommend the membrane system or repair approach that fits the roof.

Certified installer for GAF, CertainTeed and Owens Corning, family-owned, licensed & insured.

Courtland Roofing has worked on flat roofs in every part of South Jordan, Utah (84095 and 84009), including the streets around Daybreak and Oquirrh Lake. We give homeowners across the rest of Salt Lake County the same service, including in Taylorsville, Murray and Draper.

If you do not see your ZIP code listed, call or text us. We can confirm whether we provide flat and low-slope roofing at your address in South Jordan.