Flat and Low-Slope Roofing in Heber City, Utah

A low-slope roof depends more on waterproof membrane continuity than on gravity alone, which makes membrane seams, drainage, edges and roof openings especially important.

Median year built from the US Census American Community Survey; elevation from USGS.

You should have a low-slope roof checked when ponding, loose seams, bubbles, cracks or water staining appear, so we can determine whether the problem starts with drainage, the membrane or both.

The membrane is only one part of wind resistance on a low-slope roof because a strong membrane can still fail if perimeter details are loose.

We pay close attention to drainage because low-slope roofs can hold water in shallow areas, and we note where water collects or has trouble reaching an exit point.

Flat roofs can carry snow and meltwater for longer periods, and the roof needs a clear path for that meltwater to reach drains or scuppers.

We compare TPO, EPDM and modified bitumen for flat and low-slope roofs; drainage, roof details and the existing assembly guide the choice.

• TPO single-ply membrane: The TPO system uses a thermoplastic roofing sheet; heat-welded seams connect adjacent sheets into one continuous surface.
• EPDM rubber membrane: The EPDM system relies on a flexible rubber sheet; installers join seams with compatible tapes or adhesives and use matching flashing products at details.
• Modified bitumen: The modified-bitumen system uses reinforced asphalt-based roofing sheets; it is often practical on garages, porches and smaller low-slope sections.
• Existing membrane repairs: We check the current membrane for open joints, punctures and failed flashing; we inspect the drainage system for conditions that may be contributing to the damage.

Before planning low-slope roofing work, we first evaluate how the roof drains; we also check the membrane, roof base, seams, edges and roof openings before deciding what needs work.

• Build roof edges and transitions: We complete perimeter edges and wall transitions with secure membrane terminations; proper termination helps prevent water or wind from getting behind the roofing.
• Check the roof base and insulation: We look below the membrane surface for wet insulation and damaged roof-base materials; we correct conditions that would leave the new membrane over a failing base.
• Test and inspect seams: Our final review includes the membrane seams and detailed transitions; applicable systems may also allow seams to be probed or otherwise tested.
• Detail drains and roof openings: We tie each drain or roof opening into the membrane with compatible flashing; the detail has to stay watertight where the flat roof is interrupted.
• Prepare the roof surface: The roof surface has to be clean and sound before the new membrane goes down; we remove or prepare existing materials according to the condition of the roof.
• Assess drainage first: We map water movement across the roof and identify recurring low areas; the drainage pattern helps separate membrane problems from water-flow problems.

Which of those apply depends on what the inspection finds. We would rather tell you the roof needs a repair than sell you a replacement it does not need yet.

For the full picture of the service, see Flat Roofing.

We approach low-slope roofing differently from steep-slope shingle work because the drainage path and continuous membrane have to work before the roof can keep water out.

1. Inspect the existing roofWe examine membrane condition, drainage and roof openings; we record damaged areas or locations that hold water.
2. Confirm the roofing approachAfter the inspection, we decide whether to repair the roof, install a new membrane over suitable existing roofing or replace it; we do not assume every low-slope roof needs full replacement.
3. Correct problems below the membraneWe address problem areas below the membrane before the new roof covers them; the finished roof should sit over sound materials.
4. Install the low-slope roofing systemWe install the new membrane according to the requirements of the selected material; we use compatible seam and flashing materials.
5. Check drainage and detailsWe finish by reviewing the places where water leaves the roof or the membrane changes direction; we check that runoff is directed away from vulnerable details.

Courtland Roofing provides low-slope roofing service for membrane roofs and flat roof sections; we base the recommendation on membrane condition, drainage and materials below the surface.

Certified installer for GAF, CertainTeed and Owens Corning, family-owned, licensed & insured.

Courtland Roofing has worked on flat roofs in every part of Heber City, Utah (84032), including the streets around the Heber Valley Railroad and Jordanelle Reservoir. We give homeowners across the rest of Surrounding Areas the same service, including in Park City, Midway and Morgan.

If you do not see your ZIP code listed, call or text us. We can confirm whether we provide flat and low-slope roofing at your address in Heber City.