Flat and Low-Slope Roofing in Grantsville, Utah

Flat roofs need a different roofing approach because runoff moves more slowly, so every joint, edge and opening has to remain watertight while water moves toward drainage.

Median year built from the US Census American Community Survey; elevation from USGS.

A flat roof needs attention when water remains after normal drainage or the membrane starts showing damage before trapped moisture or recurring ponding causes more damage.

Walls, roof curbs, vents and equipment create important flashing details on a flat roof, and the membrane has to stay continuous through each change in direction.

Snow does not slide from a flat roof as readily as it does from many steep roofs, and the membrane has to stay watertight while the drainage system clears the water.

Roof-surface heat is part of the material choice on an exposed flat roof, although the overall building response depends on more than the roofing color alone.

Low-slope roofs can use TPO, EPDM or modified-bitumen membranes; the choice depends on how the roof is built, drained and used.

• TPO single-ply membrane: TPO roofing uses a thermoplastic membrane; installers heat-weld adjoining sheets to create a continuous water-resistant surface.
• EPDM rubber membrane: EPDM roofing uses a durable rubber membrane; compatible seam and flashing products complete the joints and transitions.
• Modified bitumen: Modified-bitumen roofing combines asphalt with reinforcement for low-slope applications; it can be practical where a reinforced asphalt membrane fits the roof design.
• Existing membrane repairs: Existing membrane repairs begin with an inspection of seams, flashing and damaged surface areas; we separate repairable damage from conditions that point to replacement.

Drainage is the starting point for a low-slope roofing project; we include roof openings, edges and seams in the same water-control evaluation.

• Detail drains and roof openings: We build membrane flashing around drains, pipes, vents, skylight curbs, walls and equipment; the membrane and flashing work together to keep the transition watertight.
• Install the membrane: We install the membrane using the layout and attachment method specified for that roof; we inspect the seams as part of the completed membrane installation.
• Check the roof base and insulation: We inspect the roof base and insulation before they are covered; we use the results to decide what can safely remain in place.
• Prepare the roof surface: We prepare a stable roof surface before installing the membrane; the existing roof assembly guides the preparation method.
• Assess drainage first: We look at how runoff reaches drains, scuppers, gutters and roof edges; we address drainage problems that could cause the same damage to return.
• Test and inspect seams: We check each completed seam and critical detail before the roof is considered finished; we confirm that the seam work matches the selected roofing system.

Which of those apply depends on what the inspection finds. We would rather tell you the roof needs a repair than sell you a replacement it does not need yet.

For the full picture of the service, see Flat Roofing.

A flat-roof project has a different order of work than a shingle roof since slow drainage makes membrane continuity and water-control details especially important.

1. Inspect the existing roofWe review the existing roof surface, drainage and previous repairs; we document the conditions that matter before work begins.
2. Confirm the roofing approachThe existing roof condition determines whether we repair it, install new roofing over suitable existing materials or replace it; we choose the least extensive approach that still solves the roofing problem.
3. Correct problems below the membraneWe remove or repair wet and damaged materials that should not remain below the new membrane; we complete this work before the roof is closed up.
4. Install the low-slope roofing systemWe lay out and secure the chosen membrane system; the selected product determines how the sheets are attached and joined.
5. Check drainage and detailsWe check the completed roof at drains, scuppers, walls, curbs and roof openings; we use the final review to catch small detail problems before the job is finished.

Homeowners can call Courtland Roofing for flat-roof repair, replacement and membrane installation; we base our recommendation on the roof's actual condition.

Certified installer for GAF, CertainTeed and Owens Corning, family-owned, licensed & insured.

Courtland Roofing has worked on flat roofs in every part of Grantsville, Utah (84029), and we would be glad to look at yours. We give homeowners across the rest of Surrounding Areas the same service, including in Heber City, Midway and Morgan.

If you do not see your ZIP code listed, call or text us. We can confirm whether we provide flat and low-slope roofing at your address in Grantsville.