Flat and Low-Slope Roofing in Copperton, Utah

A flat or low-slope roof cannot rely on overlapping shingles to shed water quickly, which means drains, flashing, seams and roof openings need careful detailing.

Median year built from the US Census American Community Survey; elevation from USGS.

Recurring standing water, open seams, membrane cracks or interior stains are reasons to inspect a low-slope roof because standing water can keep pressure on weak seams and roof openings.

Low-slope membranes receive long periods of direct sun during summer; but membrane color is only one part of the building's heat performance.

A low-slope roof may hold snow for an extended period before it melts or drains, and recurring ponding should not be treated as normal simply because the roof is flat.

Low-slope roofs need secure membrane and edge attachment in exposed conditions, so corners, parapets and equipment transitions are part of the wind review.

TPO, EPDM and modified bitumen are the primary low-slope roofing systems we evaluate; each system uses different seam and flashing methods.

• TPO single-ply membrane: A TPO roof uses a thermoplastic single-ply membrane; installers use heat-welding equipment to join the sheets at their seams.
• EPDM rubber membrane: An EPDM roof uses a flexible synthetic rubber membrane; seams are completed with materials designed specifically for the EPDM system.
• Modified bitumen: A modified-bitumen roof uses reinforced asphalt-based membrane sheets; it can suit compact roof sections where an asphalt-based membrane is appropriate.
• Existing membrane repairs: We evaluate existing flat-roof membranes for seam openings, punctures and flashing damage; we check whether an isolated repair will address the underlying cause.

We start a low-slope roofing project by understanding how water moves across the roof; we inspect the membrane, underlying roof base, seams, perimeter edges and roof openings as one system.

• Test and inspect seams: We give the completed membrane seams and details a final inspection; we verify continuity using the method appropriate for the roofing material.
• Detail drains and roof openings: Drains and roof openings receive membrane flashing designed for the selected roofing system; the flashing keeps water moving toward drainage instead of into the roof.
• Build roof edges and transitions: Roof edges, parapets, walls and termination points receive dedicated membrane details; these exposed locations need dependable attachment and water-control details.
• Install the membrane: We position and secure the membrane using the attachment method required for the system; we use the seam technique specified for TPO, EPDM or modified bitumen.
• Assess drainage first: We trace the roof's drainage path and note areas where water tends to stand; the results help determine whether the roof needs membrane work, drainage work or both.
• Check the roof base and insulation: We check the materials below the membrane for moisture, damaged insulation and weak areas; we want the new membrane installed over sound, dry materials.

Which of those apply depends on what the inspection finds. We would rather tell you the roof needs a repair than sell you a replacement it does not need yet.

For the full picture of the service, see Flat Roofing.

Low-slope roofing follows a different installation sequence from shingles because water control depends on drainage, seams and membrane continuity rather than overlapping shingles.

1. Inspect the existing roofWe inspect the current membrane, drainage and perimeter details; we use the inspection to decide whether repair or replacement is appropriate.
2. Confirm the roofing approachWe compare four options: repair, partial replacement, a new membrane over suitable existing roofing and full removal; the scope should match the actual extent of the problem.
3. Correct problems below the membraneWe correct wet insulation, weak roof-base areas and other unsound materials first; the goal is a stable, dry base for the new roofing system.
4. Install the low-slope roofing systemWe install the selected low-slope membrane with its required attachment method; the attachment and seam details follow the selected system.
5. Check drainage and detailsThe final inspection covers drainage points, edges and membrane transitions; we verify that drainage and waterproofing work together.

Courtland Roofing handles TPO, EPDM, modified-bitumen and other low-slope roofing work; we evaluate the whole roof system rather than the membrane surface alone.

Certified installer for GAF, CertainTeed and Owens Corning, family-owned, licensed & insured.

Courtland Roofing has worked on flat roofs in every part of Copperton, Utah (84006), including the streets around the Bingham Canyon Mine. We give homeowners across the rest of Salt Lake County the same service, including in Draper, Riverton and Herriman.

If you do not see your ZIP code listed, call or text us. We can confirm whether we provide flat and low-slope roofing at your address in Copperton.