Flat and Low-Slope Roofing in Springville, Utah

A flat roof needs continuous waterproofing because water does not leave the surface as quickly, so seams, drains, roof openings, edges and the roof base all become critical parts of the waterproof system.

Median year built from the US Census American Community Survey; elevation from USGS.

A flat roof deserves attention when drainage slows, seams move or signs of moisture show up inside because the inspection can separate a drainage problem from membrane failure.

Flat-roof skylights need more than surface sealant around the frame, so the membrane has to turn up the curb and remain sealed at every corner.

Flat-roof flashing is especially important where the membrane meets vertical surfaces, so each transition has to remain watertight as water moves across the roof.

Weather damage may affect the membrane, roof edges or the routes water uses to drain, so we inspect both the roofing surface and the way water is leaving the roof.

TPO, EPDM and modified bitumen provide different ways to waterproof a low-slope roof; we choose between them based on drainage, roof size, foot traffic, existing construction and budget.

• TPO single-ply membrane: TPO uses a thermoplastic sheet as the main roof membrane; installers heat-weld the seams to join separate sheets into a continuous roof surface.
• EPDM rubber membrane: EPDM uses a synthetic rubber sheet as the main roof membrane; seams and roof details use compatible tapes, adhesives and flashing materials.
• Modified bitumen: Modified bitumen uses reinforced asphalt sheets as the main roof membrane; it can work well on smaller flat sections, porches, garages and other compact roof areas.
• Existing membrane repairs: We inspect existing low-slope roofing for failed seams, punctures and damaged flashing; we also check drainage before deciding whether repair or replacement makes sense.

Before choosing the work, we evaluate how the roof currently manages water; we then inspect the membrane, roof base, seams, edges and roof openings.

• Detail drains and roof openings: Membrane flashing is installed at drains, walls, curbs and other roof openings; the flashing directs water away from the opening.
• Check the roof base and insulation: We look for trapped moisture and damaged materials in the roof base and insulation; we address problem areas before the new membrane hides them.
• Build roof edges and transitions: Perimeter edges, parapets and wall transitions are tied into the membrane system; these details keep wind and water from working behind the membrane.
• Assess drainage first: The drainage review follows runoff from the roof surface to its exit points; we use that information to decide whether drainage changes belong in the roofing work.
• Prepare the roof surface: We prepare the roof base so the membrane is not installed over loose or unsound material; the existing assembly determines whether the project needs tear-off, installing new roofing over suitable existing materials or insulation replacement.
• Test and inspect seams: We review the installed seams and transitions as part of the final quality check; we use the inspection method appropriate for the selected membrane system.

Which of those apply depends on what the inspection finds. We would rather tell you the roof needs a repair than sell you a replacement it does not need yet.

For the full picture of the service, see Flat Roofing.

The installation order changes when the roof uses a membrane instead of shingles because drainage and membrane continuity must be established before the roof is watertight.

1. Inspect the existing roofWe examine the roof surface, edges, openings and drainage; we also note roof openings, repairs and areas that stay wet.
2. Confirm the roofing approachWe compare the available repair and replacement approaches; we base that decision on membrane condition, moisture and drainage.
3. Correct problems below the membraneWe repair or remove unsound materials that could compromise the new membrane; the new membrane should not be installed over a failing base.
4. Install the low-slope roofing systemWe complete the main membrane surface with the selected low-slope system; we complete the seams with the method designed for that material.
5. Check drainage and detailsThe last review focuses on drainage and the detailed areas around edges and openings; we confirm that water has a clear path off the finished roof.

We provide flat and low-slope roofing service through Courtland Roofing; we inspect drainage, moisture and the roof base before recommending the work.

Certified installer for GAF, CertainTeed and Owens Corning, family-owned, licensed & insured.

Courtland Roofing has worked on flat roofs in every part of Springville, Utah (84663), including the streets around Hobble Creek Canyon and the Springville Museum of Art. We give homeowners across the rest of Utah County the same service, including in American Fork, Payson and Saratoga Springs.

If you do not see your ZIP code listed, call or text us. We can confirm whether we provide flat and low-slope roofing at your address in Springville.