Flat and Low-Slope Roofing in Hooper, Utah

A low-slope roof depends more on waterproof membrane continuity than on gravity alone, which makes drainage paths and membrane details central to the installation.

Median year built from the US Census American Community Survey; elevation from USGS.

You should have a low-slope roof checked when ponding, loose seams, bubbles, cracks or water staining appear, and we use the inspection to determine whether repair or replacement is appropriate.

A flat roof can absorb substantial solar heat because much of the membrane faces the sky directly while insulation and the construction below the roof still affect indoor conditions.

Low-slope roofing has to turn up and seal around skylight curbs, and the flashing has to stay continuous where horizontal roofing meets the raised curb.

Winter conditions can slow drainage when ice forms near scuppers, drains or edges, and we pay attention to places where snowmelt repeatedly collects.

We compare TPO, EPDM and modified bitumen for flat and low-slope roofs; we compare the systems against the actual condition and use of the roof.

• TPO single-ply membrane: The TPO system uses a thermoplastic roofing sheet; the sheets are joined with heat-welded seams rather than overlapping shingle-style joints.
• EPDM rubber membrane: The EPDM system relies on a flexible rubber sheet; the joining method relies on EPDM-compatible tapes, adhesives and flashing products.
• Modified bitumen: The modified-bitumen system uses reinforced asphalt-based roofing sheets; it can be useful on porches, garages and other modest low-slope areas.
• Existing membrane repairs: We check the current membrane for open joints, punctures and failed flashing; we include drainage in the recommendation so the same problem is less likely to return.

Before planning low-slope roofing work, we first evaluate how the roof drains; we evaluate seams, edges and roof openings along with the drainage system.

• Test and inspect seams: Our final review includes the membrane seams and detailed transitions; we check for gaps or incomplete joints using the method suited to the system.
• Install the membrane: We lay out the selected membrane and secure it as the system requires; the seam work follows the requirements of the selected roofing system.
• Build roof edges and transitions: We complete perimeter edges and wall transitions with secure membrane terminations; careful edge work helps keep the membrane secure at exposed perimeter locations.
• Prepare the roof surface: The roof surface has to be clean and sound before the new membrane goes down; we prepare or remove existing layers as needed before the new membrane is installed.
• Detail drains and roof openings: We tie each drain or roof opening into the membrane with compatible flashing; the selected roofing system determines the exact flashing materials and method.
• Check the roof base and insulation: We look below the membrane surface for wet insulation and damaged roof-base materials; this keeps the new roof from trapping an existing moisture problem.

Which of those apply depends on what the inspection finds. We would rather tell you the roof needs a repair than sell you a replacement it does not need yet.

For the full picture of the service, see Flat Roofing.

We approach low-slope roofing differently from steep-slope shingle work because seams, drainage and membrane details must be completed as one water-control system.

1. Inspect the existing roofWe examine membrane condition, drainage and roof openings; we identify conditions that may affect the new roofing.
2. Confirm the roofing approachAfter the inspection, we decide whether to repair the roof, install a new membrane over suitable existing roofing or replace it; we decide what can safely remain before new roofing is installed.
3. Correct problems below the membraneWe address problem areas below the membrane before the new roof covers them; the new roof should not depend on damaged material underneath.
4. Install the low-slope roofing systemWe install the new membrane according to the requirements of the selected material; we complete the system-specific seam work before final inspection.
5. Check drainage and detailsWe finish by reviewing the places where water leaves the roof or the membrane changes direction; we check common leak points before sign-off.

Courtland Roofing provides low-slope roofing service for membrane roofs and flat roof sections; we treat drainage and trapped moisture as part of the roofing problem.

Certified installer for GAF, CertainTeed and Owens Corning, family-owned, licensed & insured.

Courtland Roofing has worked on flat roofs in every part of Hooper, Utah (84315), including the streets around the Great Salt Lake shoreline. We give homeowners across the rest of Weber County the same service, including in Marriott-Slaterville, Uintah and Huntsville.

If you do not see your ZIP code listed, call or text us. We can confirm whether we provide flat and low-slope roofing at your address in Hooper.