Flat and Low-Slope Roofing in Eden, Utah

A flat or low-slope roof cannot rely on overlapping shingles to shed water quickly, which is why the roof base, membrane seams and drainage layout all matter.

Median year built from the US Census American Community Survey; elevation from USGS.

Recurring standing water, open seams, membrane cracks or interior stains are reasons to inspect a low-slope roof, so we can identify whether the problem is isolated or spread across the roof.

We check for trapped moisture below a low-slope roof, not just surface damage because moisture below the surface can shorten the life of the roofing system.

Low-slope roofs need secure membrane and edge attachment in exposed conditions because wind damage often starts at exposed edges rather than the middle of the roof.

We start the weather review by looking at how the roof drains, and we trace how water gets from the membrane to the roof's drainage points.

TPO, EPDM and modified bitumen are the primary low-slope roofing systems we evaluate; the existing roof and water-control details help determine which system fits best.

• TPO single-ply membrane: A TPO roof uses a thermoplastic single-ply membrane; the seams are welded with heat so the separate sheets act as one membrane.
• EPDM rubber membrane: An EPDM roof uses a flexible synthetic rubber membrane; the membrane is joined and flashed with materials compatible with EPDM.
• Modified bitumen: A modified-bitumen roof uses reinforced asphalt-based membrane sheets; it is commonly considered for smaller flat sections and other low-slope areas.
• Existing membrane repairs: We evaluate existing flat-roof membranes for seam openings, punctures and flashing damage; we evaluate both membrane damage and water movement before choosing the next step.

We start a low-slope roofing project by understanding how water moves across the roof; we use the drainage pattern and membrane condition to guide the project scope.

• Install the membrane: We position and secure the membrane using the attachment method required for the system; the selected material determines how adjoining sheets become a continuous waterproof surface.
• Prepare the roof surface: A new membrane needs a sound, clean surface underneath it; we do not cover loose, wet or unsound materials with the new membrane.
• Assess drainage first: We trace the roof's drainage path and note areas where water tends to stand; the inspection shows whether runoff is reaching its intended exit points.
• Detail drains and roof openings: Drains and roof openings receive membrane flashing designed for the selected roofing system; these details keep roof openings from becoming weak points.
• Test and inspect seams: We give the completed membrane seams and details a final inspection; we correct incomplete seam details before considering the roof finished.
• Check the roof base and insulation: We check the materials below the membrane for moisture, damaged insulation and weak areas; the roof should not be closed up over damaged or wet materials.

Which of those apply depends on what the inspection finds. We would rather tell you the roof needs a repair than sell you a replacement it does not need yet.

For the full picture of the service, see Flat Roofing.

Low-slope roofing follows a different installation sequence from shingles because the roof becomes watertight only after the membrane and drainage details are completed.

1. Inspect the existing roofWe inspect the current membrane, drainage and perimeter details; we use the findings to plan the next step.
2. Confirm the roofing approachWe compare four options: repair, partial replacement, a new membrane over suitable existing roofing and full removal; the recommendation reflects both the visible membrane and materials below it.
3. Correct problems below the membraneWe correct wet insulation, weak roof-base areas and other unsound materials first; the corrected roof base gives the membrane a sound surface.
4. Install the low-slope roofing systemWe install the selected low-slope membrane with its required attachment method; we install the membrane and seams as one roofing system.
5. Check drainage and detailsThe final inspection covers drainage points, edges and membrane transitions; we verify that drains and transitions are complete.

Courtland Roofing handles TPO, EPDM, modified-bitumen and other low-slope roofing work; we plan the work around both waterproofing and water movement.

Certified installer for GAF, CertainTeed and Owens Corning, family-owned, licensed & insured.

Courtland Roofing has worked on flat roofs in every part of Eden, Utah (84310), including the streets around Powder Mountain and Pineview Reservoir. We give homeowners across the rest of Weber County the same service, including in Liberty, Nordic Valley and Ogden.

If you do not see your ZIP code listed, call or text us. We can confirm whether we provide flat and low-slope roofing at your address in Eden.