Flat and Low-Slope Roofing in Syracuse, Utah

A flat roof needs continuous waterproofing because water does not leave the surface as quickly, which means drains, flashing, seams and roof openings need careful detailing.

Median year built from the US Census American Community Survey; elevation from USGS.

A flat roof deserves attention when drainage slows, seams move or signs of moisture show up inside because standing water can keep pressure on weak seams and roof openings.

Solar exposure matters when choosing between membrane colors and finishes; but membrane color is only one part of the building's heat performance.

Winter water control depends on keeping drains and roof edges able to move snowmelt, so drains, scuppers and edges are part of the winter roof review.

The roof's ability to move water is one of the first conditions we review, and compare ponding areas with the location of drains, scuppers and roof edges.

TPO, EPDM and modified bitumen provide different ways to waterproof a low-slope roof; each system uses different seam and flashing methods.

• TPO single-ply membrane: TPO uses a thermoplastic sheet as the main roof membrane; installers use heat-welding equipment to join the sheets at their seams.
• EPDM rubber membrane: EPDM uses a synthetic rubber sheet as the main roof membrane; seams are completed with materials designed specifically for the EPDM system.
• Modified bitumen: Modified bitumen uses reinforced asphalt sheets as the main roof membrane; it can suit compact roof sections where an asphalt-based membrane is appropriate.
• Existing membrane repairs: We inspect existing low-slope roofing for failed seams, punctures and damaged flashing; we check whether an isolated repair will address the underlying cause.

Before choosing the work, we evaluate how the roof currently manages water; we inspect the membrane, underlying roof base, seams, perimeter edges and roof openings as one system.

• Check the roof base and insulation: We look for trapped moisture and damaged materials in the roof base and insulation; we want the new membrane installed over sound, dry materials.
• Install the membrane: We secure the membrane with the attachment method that matches the chosen roof system; we use the seam technique specified for TPO, EPDM or modified bitumen.
• Test and inspect seams: We review the installed seams and transitions as part of the final quality check; we verify continuity using the method appropriate for the roofing material.
• Detail drains and roof openings: Membrane flashing is installed at drains, walls, curbs and other roof openings; the flashing keeps water moving toward drainage instead of into the roof.
• Assess drainage first: The drainage review follows runoff from the roof surface to its exit points; the results help determine whether the roof needs membrane work, drainage work or both.
• Build roof edges and transitions: Perimeter edges, parapets and wall transitions are tied into the membrane system; these exposed locations need dependable attachment and water-control details.

Which of those apply depends on what the inspection finds. We would rather tell you the roof needs a repair than sell you a replacement it does not need yet.

For the full picture of the service, see Flat Roofing.

The installation order changes when the roof uses a membrane instead of shingles because water control depends on drainage, seams and membrane continuity rather than overlapping shingles.

1. Inspect the existing roofWe examine the roof surface, edges, openings and drainage; we use the inspection to decide whether repair or replacement is appropriate.
2. Confirm the roofing approachWe compare the available repair and replacement approaches; the scope should match the actual extent of the problem.
3. Correct problems below the membraneWe repair or remove unsound materials that could compromise the new membrane; the goal is a stable, dry base for the new roofing system.
4. Install the low-slope roofing systemWe complete the main membrane surface with the selected low-slope system; the attachment and seam details follow the selected system.
5. Check drainage and detailsThe last review focuses on drainage and the detailed areas around edges and openings; we verify that drainage and waterproofing work together.

We provide flat and low-slope roofing service through Courtland Roofing; we evaluate the whole roof system rather than the membrane surface alone.

Certified installer for GAF, CertainTeed and Owens Corning, family-owned, licensed & insured.

Courtland Roofing has worked on flat roofs in every part of Syracuse, Utah (84075), including the streets around the Antelope Island causeway. We give homeowners across the rest of Davis County the same service, including in Sunset, West Point and South Weber.

If you do not see your ZIP code listed, call or text us. We can confirm whether we provide flat and low-slope roofing at your address in Syracuse.