Clay and Concrete Tile Roof Repair and Replacement in Millcreek, Utah

Clay and concrete tile can remain in service for many years because the tile itself often outlasts some of the materials installed below it, but the underlayment below can wear out sooner than the visible tile.

Median year built from the US Census American Community Survey; elevation from USGS.

A tile roof should be evaluated when cracked pieces, slipping tile, leaks near transitions or interior staining develops, because a leak can come from one damaged piece or from a larger problem below the tile.

Older tile roofs in Millcreek may contain previous repairs or partial underlayment work, so we inspect the existing layers before deciding whether the current problem is isolated or more widespread.

Tile-roof leaks are not always visible from the surface, so attic or interior staining can provide important location clues helping us focus on the roof details most likely to be allowing water inside.

Storms can crack or shift individual tiles in Millcreek, and we inspect the nearby underlayment and flashing when visible damage may have exposed the waterproof layer below.

A tile roof combines a durable tile surface that directs most water downhill with attachment, waterproofing and drainage details beneath the surface.

• Clay tile: Clay tile is made from fired clay and keeps its basic material strength through years of weather exposure, but the hard surface is not immune to impact damage.
• Concrete tile: Concrete tile is a heavy tile product with a range of appearance options, so the home must be appropriate for the product being installed.
• Underlayment: Underlayment acts as the hidden water barrier beneath the tile, and the tile above may remain usable long after this layer begins to age.
• Battens and attachment: Some tile systems rely on battens to help align the surface pieces, and the support and fastening details need to keep the tile secure without blocking drainage.
• Flashing and valleys: Flashing routes water around roof joints and concentrated drainage areas, and we check these locations closely when water is entering near a joint.

Tile-roof work can range from replacing a few cracked or slipped tiles to renewing the hidden waterproofing beneath much of the roof, so the inspection determines which level of work matches the failure.

• Broken tile replacement: When damage is limited to one small area, we replace the damaged tiles and leave the surrounding roof intact, and we also check the exposed underlayment and attachment below.
• Flashing repair and replacement: When flashing fails around walls, vents and other roof joints, we rebuild the failed transition with properly integrated flashing, so water is directed away from the joint and back onto the roof surface.
• Valley repair: For a leaking or poorly draining valley, we inspect the full valley detail from the upper section to the lower edge, so debris and damaged materials no longer interfere with the water path.
• Ridge and hip tile repair: When ridge or hip pieces no longer sit securely, we restore the supporting detail before the cap tile goes back.
• Lift-and-relay underlayment replacement: We lift the original tile that remains in good condition, then replace aging underlayment and correct failed flashing details before the saved tile is installed again.
• Full tile roof replacement: Full replacement makes sense when the roof design is changing and requires a new tile system, and the replacement scope matches the full extent of the failure.

Which of these your roof needs comes out of the inspection. The tiles usually outlive everything else up there, so we would rather relay yours than sell you new ones.

For the full picture of the service, see Clay & Concrete Tile Roofing.

Lift-and-relay underlayment replacement preserves reusable tile while replacing the water barrier beneath the tile, which lets us correct hidden problems before the roof is closed again.

1. Lift and organize the tileWe lift the pieces that will be reinstalled, and replacement needs become clear before the later relay.
2. Remove the old underlaymentAfter the tile is removed, we remove the old water barrier to expose the supporting wood, so we can inspect valleys, flashing and supporting materials below.
3. Repair damaged woodIf we find soft wood beneath the waterproofing, we document the affected wood and explain the repair before replacing the affected material.
4. Install new tile-compatible underlaymentWe install a new waterproofing layer after the deck repairs are complete and finish the drainage details that protect the roof deck below.
5. Relay the tileAfter the waterproofing is complete, we return reusable tile over the renewed waterproofing, and inspect the completed area.

Courtland Roofing handles clay and concrete tile repair, underlayment replacement and full tile-roof replacement in Millcreek, and we explain whether the problem is limited to one area or affects a larger part of the roof.

Certified installer for GAF, CertainTeed and Owens Corning, family-owned, licensed & insured.

Courtland Roofing has worked on tile roofs in every part of Millcreek, Utah, including Mount Olympus, East Millcreek and Canyon Rim. Those are Millcreek neighborhoods we have worked in, and they are examples, not a boundary:

If you do not see your street listed, call or text us. We can confirm whether we provide clay and concrete tile roofing at your address in Millcreek.